AirPods Max Not Turning On? 5 Complete Steps for Fix It

You grab your headphones, put them on, and get silence. No chime, no connection pop-up on your iPhone, nothing. You press the Digital Crown. Nothing. You press it harder, like that ever helped. If your AirPods Max not turning on is the whole story right now, here’s the good news: a headset that looks dead is very often just a headset with an empty battery that needs a proper charge.

Here’s the thing about AirPods Max. There’s no power button. They don’t switch off like a normal gadget. They sit in a low-power state, and the Smart Case pushes them into an even deeper one. So when they seem dead, it’s usually one of three things: the battery drained to zero while they sat unused, the charge isn’t actually reaching them, or they’re stuck in a weird state that a reset clears.

This guide covers all of it. A forced charge done the right way, the reset combo, firmware and update trouble (including after a USB-C update or if you just have the USB-C model), and when it’s time to hand them to Apple. Plus a table that compares charging setups, because the wrong cable or adapter is behind a lot of “dead” headsets.

Quick answers:

No light, no sound, nothing at all: Battery drained to zero. Charge on a wall adapter with a known-good cable for at least 30 minutes, then check again.
Light flashes amber or white but won’t connect: They’re alive and need a reset. Hold the noise control button and the Digital Crown together for 15 seconds.
Turns on, then dies fast: Worn battery or a stuck state. Reset, update and run a full charge cycle, then look at battery health.
Dead right after a firmware update: They were likely mid-update on a low battery. Charge them fully while connected, then reset.

Why AirPods Max Won’t Turn On

Short list. Almost everything that makes AirPods Max look dead falls into these buckets.

The battery is completely drained. Left in a drawer or in the Smart Case for weeks, the battery can drop to zero. A fully flat headset doesn’t light up or respond at all, and it can take a while on the charger before it shows any sign of life.

The power isn’t getting through. A bad cable, a weak adapter, a computer port that barely trickles, a dirty charging port or a cable that doesn’t quite seat. The headset looks dead because it’s starving.

They’re stuck in a deep low-power state. The Smart Case puts them into an ultra-low-power state, and sometimes they don’t wake up cleanly. They look off, but they’re just refusing to answer.

A software or firmware glitch. A bad connection state, a half-finished update or a glitch after an update can leave the headset unresponsive until you reset it.

A worn battery or a hardware fault. After a couple of years, capacity drops. And in rare cases, the charging circuit or battery has failed outright. That’s the last suspect, not the first.

AirPods Max Digital Crown noise control button and charging port locations

Fix 1: Do a Proper Forced Charge

Start here. A real forced charge fixes more “dead” AirPods Max than everything else combined. And no, five minutes isn’t a real charge.

Step 1: Use the right cable and a wall adapter.

Use the charging cable that came with your AirPods Max, or one you know charges other devices reliably
Plug it into a normal wall adapter, not a laptop port, USB hub or car charger
Check which port you have: Lightning on the original model, USB-C on the newer one
Plug the cable firmly into the port on the bottom of the right ear cup

Cheap or worn cables can charge a phone and still fail the headset. A weak computer port might wake the light for a second and then quit. A plain wall adapter with a good cable removes both problems in one go.

Step 2: Leave them alone for at least 30 minutes.

Keep the headset plugged in and untouched
Don't unplug every few minutes to check, it restarts the wait
Look at the status light at the bottom of the right ear cup after the wait
Amber = charging, Green = fully charged, No light = still no power reaching them

A headset drained to zero can sit there lifeless for a surprisingly long time before the light finally appears. Every time you unplug it to peek, you reset the clock. Give it a full half hour. If you see nothing, give it a couple of hours. Be patient. Let it cook.

Step 3: Try a second cable and a second adapter.

Swap the cable for another known-good one
Swap the adapter or the wall outlet
Test the outlet with a lamp or phone charger
Retry for another 30 minutes

Changing one thing at a time tells you where the problem lives. If a different cable wakes it up, the first cable was the problem. If nothing changes after a different cable, adapter and outlet, power delivery isn’t the issue.

Read More: AirPods case not charging? 5 fixes that work

Fix 2: Clean the Charging Port

If a good cable and adapter changed nothing, check the port. Lint and dust in a charging port are sneaky, and they cause a lot of “dead” headsets.

Step 1: Look inside the port.

Unplug the cable and hold the headset in good light
Shine a phone flashlight into the port on the bottom of the right ear cup
Gray fuzz or a solid-looking plug at the bottom = lint buildup
Check the cable plug too for bent pins, grime or discolored metal

Step 2: Clean it gently.

Use a wooden or plastic toothpick, never metal
Scrape along the walls and lift the lint out, don't jab the center
Do NOT use compressed air, it packs debris deeper
Wipe the cable plug with a dry cotton swab
Retry the forced charge for 30 minutes

Go slow. The contacts are delicate and a metal pick can bend or short them. Wood is soft enough to be safe and firm enough to pull out a lint plug in one piece. Most people are shocked by how much comes out. And yes, a packed port makes the cable look connected while nothing actually touches.

AirPods Max charging port cleaning and USB C cable inspection

Which Charging Setup Works Best? Options Compared

Here’s the thing. A lot of people blame the headset when the problem is what they’re charging it from. Different setups behave very differently, and knowing which one you’re using tells you where to look.

Charge Source Works With Power Reliability Common Problem How to Test It Best Use Avoid When
Wall adapter with original cable Both original and USB-C models, using the cable for your model High Worn or loose cable, dirty port Swap in a second known-good cable and wait 30 minutes Forced charge and everyday charging Never, this is your baseline
USB-C to USB-C cable on a wall adapter USB-C model High Cheap cable carrying weak power or data only Charge a phone with the same cable, then retry the headset Charging the newer model The cable is bent, frayed or unbranded and flaky
USB-C to Lightning cable on a wall adapter Original Lightning model High Frayed connector, loose-fitting third-party cable Test with another known-good Lightning cable Charging the original model The connector shows damage or bent pins
USB-A to USB-C or Lightning cable on an old adapter Both, with the right cable end Medium Underpowered old adapter Retry with a newer wall adapter Backup option The adapter is old or unbranded
Laptop or computer USB port Both Low to medium Port trickles too little power to wake a drained battery Compare with a wall adapter Topping up when nothing else is around The battery is fully drained or you’re troubleshooting
USB hub or dock Both Low Shared power, drops in and out Plug directly into a wall adapter instead Rarely Always when troubleshooting a dead headset
Car charger Both Low to medium Cuts in and out with the engine, weak output Retry at home on a wall adapter Emergency top-up You’re trying to wake a flat battery
Power bank Both Medium Low-current mode that shuts off for small devices Try a different port on the bank or a wall adapter Travel You can’t confirm it charges small devices reliably

My honest advice: when a headset looks dead, use a wall adapter and a good cable. Every time. It’s the one setup that removes the most variables at once. If that doesn’t wake it after 30 minutes to a couple of hours, you’ve learned the problem isn’t the charger.

Fix 3: Reset the AirPods Max

If they show a light or respond a little but still won’t behave, or if the forced charge brought them back to life but they act strange, a reset clears the stuck state.

Step 1: Make sure they’ve had some charge first.

Charge for at least 30 minutes on a wall adapter before resetting
Keep the cable plugged in during the reset if the battery is very low
Take them out of the Smart Case if they've been stored in it

Step 2: Do the reset combo.

Press and hold the noise control button and the Digital Crown together
Keep holding for about 15 seconds
Release when the status light flashes amber, then white
Reconnect them to your iPhone from scratch

A reset clears bad connection states and half-finished processes that can make a headset behave like a brick. If you see the amber flash, they’re alive and listening, and that’s already great news. Then pair them again like new: bring them close to your unlocked iPhone with the case open or the headset awake, and follow the pop-up.

Step 3: Forget and re-pair if they still won’t connect.

iPhone: Settings > Bluetooth > tap (i) next to AirPods Max > Forget This Device
Reset the headset again with the 15-second combo
Pair them again from scratch

If they turn on but won’t connect, that’s a connection problem rather than a power one, and our AirPods Max not connecting guide covers it.

Fix 4: Wake Them From the Smart Case and Check Their State

The Smart Case is great for protecting the headphones, but it also puts them into an ultra-low-power state. Sometimes they don’t wake up as quickly as you’d expect.

Step 1: Take them out and give them a moment.

Remove the headset from the Smart Case
Wait a minute or two, then press the Digital Crown once
Put them on and wait for the connection chime
Check the status light by plugging in the cable for a few seconds

Step 2: Don’t leave them in the case or a drawer for weeks.

If you won't use them for a while, charge them to a healthy level before storing them
Charge them again every month or two if they sit unused
Store in the Smart Case at room temperature, away from heat and cold

A battery that sits flat for a long time is harder to wake and ages faster. A quick top-up before storing them and an occasional check keeps the battery healthy. It’s the cheapest trick in the whole guide, and almost nobody does it.

Fix 5: Check Firmware, Updates and the USB-C Model

If your headset died right after an update, or if you have the newer USB-C model and things feel off, the firmware side deserves a look.

Step 1: Know that AirPods Max update on their own.

Firmware updates install automatically when the headset is charging, in range of its paired iPhone, and connected to Wi-Fi
You can't force an update manually
To nudge it along: plug the headset in, keep it near your iPhone on Wi-Fi and leave it for about 30 minutes
Check the version: iPhone Settings > Bluetooth > (i) next to your AirPods Max > About > Version

If an update starts while the battery is nearly flat, the headset can look dead until it has enough power to finish. Plug it in and leave it. Don’t unplug it mid-update, and give it time. Most of the time it comes back on its own.

Step 2: Update your iPhone too.

iPhone: Settings > General > Software Update
Install any available iOS update
Restart the iPhone, then re-pair the headset if it still won't connect

Step 3: If you have the USB-C model, check the cable and the setup.

Use a proper USB-C cable that carries power, ideally the one from the box
Plug into a wall adapter, not a hub
Don't mix up a data-only cable with a charging cable
If you use the wired USB-C connection for audio, unplug it and test the headset on its own first

On the newer model, plenty of “dead” headsets come down to a USB-C cable that doesn’t carry enough power or isn’t seated properly. Use the original cable first. And if the headset only fails when plugged into a certain source, that source is your answer.

AirPods Max not turning on reset process Bluetooth settings and firmware update guide

AirPods Max Not Turning On: Specific Scenarios

No Light and No Response When Plugged In

No light usually means the battery is flat, the cable isn’t delivering, or the port is blocked. Run Fix 1 and Fix 2. Wall adapter, good cable, clean port, then a full 30 minutes, then a couple of hours if needed. If there’s still no light after a couple of hours on a known-good setup, the charging circuit or battery is likely at fault and Apple should look at it.

Light Flashes Amber or White but They Won’t Connect

That’s a good sign. The headset is alive. Do the 15-second reset in Fix 3, forget the headset on your iPhone and pair it again. If the light keeps flashing and they still won’t connect after the reset and a full charge, update your iPhone and try pairing with another device to see whether the headset or your phone is the issue.

Stuck on Amber and Never Turns Green

Amber means charging. If it stays amber for many hours, the battery may not be charging fully, the cable may be weak, or the battery may be worn. Try another cable and adapter, clean the port and give it a long charge. If it still never goes green, book a battery check.

Turns On Briefly Then Dies

That usually means a worn battery or a charge that didn’t take. Charge fully, reset (Fix 3), then test how long they last. If they die within minutes after a full charge, the battery is at the end of its life and needs service.

Dead Right After a Firmware Update

Most often they were updating on a low battery. Plug them in near your iPhone on Wi-Fi, leave them for at least 30 minutes, then reset (Fix 3). If they stay unresponsive after a long charge and a reset, contact Apple.

AirPods Max awake low power and deep sleep modes comparison

Read More: AirPods keep disconnecting? Try these fixes

Final Checklist

  • Charged on a wall adapter with a known-good cable, not a laptop port, hub or car charger
  • Waited at least 30 minutes without unplugging, then a couple of hours if there was still no light
  • Tried a second cable and a second adapter or outlet
  • Looked into the charging port with a flashlight and cleared lint with a wooden toothpick
  • Checked the cable plug for bent pins, grime or damage
  • Confirmed the port type and matched the cable, Lightning or USB-C
  • Took the headset out of the Smart Case and pressed the Digital Crown
  • Reset with the noise control button and Digital Crown held for 15 seconds
  • Forgot the headset on my iPhone and paired it again
  • Kept the headset plugged in, near my iPhone on Wi-Fi, for about 30 minutes to allow a firmware update
  • Updated my iPhone to the latest iOS
  • Checked the firmware version in Settings > Bluetooth > (i) > About
  • Ran a full charge and tested how long the battery actually lasts
  • Checked coverage at checkcoverage.apple.com

When to Go to Apple Directly

You’ve charged it on a wall adapter with a good cable for hours. Cleaned the port. Reset it. Tried a second cable and adapter. Let a firmware update finish. And the headset still shows no light, never wakes up, or dies minutes after a full charge. That’s the end of the home road.

At that point the fault is inside. A dead battery cell, a failed charging circuit, a damaged port. None of it is visible and none of it responds to anything you can do at the kitchen table. Don’t try to open the ear cups either. They’re glued and clipped, and you’ll wreck them.

Check your coverage first at checkcoverage.apple.com. AirPods Max come with a one-year limited warranty, and AppleCare+ extends it. AppleCare+ can also cover battery service if capacity falls below the level in its terms. Out of warranty, Apple can quote a flat-rate service price. Book a Genius Bar or send-in repair and bring the cable and the Smart Case too. Diagnostics are free, so go before spending money on guesses.

And if your headset turns on but won’t pair or keeps dropping, the AirPods Max not connecting guide and the AirPods keep disconnecting guide cover those problems.

AirPods Max: Official Apple Product Page

FAQ: AirPods Max Not Turning On

Why won’t my AirPods Max turn on?

Most often the battery is completely drained or power isn’t reaching the headset. AirPods Max have no power button and sit in a low-power state, so a flat battery looks like a dead headset. Charge them on a wall adapter with a known-good cable for at least 30 minutes, clean the port and try a reset. If nothing works after a couple of hours of charging, the battery or charging circuit may need service.

How long should I charge AirPods Max before they turn on?

Give them at least 30 minutes on a wall adapter, and if there’s still no light, leave them for a couple of hours. A battery that’s been flat for a long time can take a while to show any sign of life. Don’t unplug them to check every few minutes, because that restarts the wait.

How do I reset AirPods Max?

Press and hold the noise control button and the Digital Crown together for about 15 seconds, until the status light flashes amber and then white. Then forget the headset on your iPhone and pair it again from scratch. Charge them for a while before resetting if the battery is very low.

Why is my AirPods Max status light not turning on?

No light means no power is reaching the headset or the battery is drained so far that it needs time to wake. Use a wall adapter and a good cable, clean the charging port with a wooden toothpick, and wait a full 30 minutes. If there’s still no light after a couple of hours on a known-good setup, contact Apple.

Can a firmware update make AirPods Max stop working?

An update can leave the headset looking dead if it started on a very low battery and couldn’t finish. Plug them in, keep them near your iPhone on Wi-Fi, and leave them for at least 30 minutes without unplugging. Then try a reset. If they stay unresponsive after a long charge and a reset, contact Apple.

Do the USB-C AirPods Max charge differently?

They use a USB-C port instead of Lightning, so you need a proper USB-C cable that carries power. The original cable from the box is the safest choice. Plug into a wall adapter rather than a hub, since cheap or data-only cables are a common cause of a headset that seems dead.

Is it worth getting the AirPods Max battery replaced?

Often, yes, if the headphones are otherwise in good shape. A battery service from Apple usually costs far less than a new pair, and AppleCare+ may cover it if capacity has dropped below the level in its terms. Check your coverage first at checkcoverage.apple.com.

Leave a Comment